VIOFO A119 Car Camera

The A119 dash cam is the sequel to the popular A118 camera. The A119 uses a similar wedge shaped form element which presents a completely discreet installation in most cars. The digital camera is produced via the chinese language manufacturer VIOFO. it’s far based at the Novatek NT96660 processor and Omnivision OV4689 CMOS sensor. that is an development over the A118 Novatek NT96650 processor and the Aptina AR0330 CMOS. The A119 has a capacitor making it more dependable in excessive temperatures than battery based cameras.

best dash cam

The A119 can report 1440p at 30fps or 1080p at 60fps with an average bitrate of 20Mbp. The advocated decision 1440p considering the fact that it’s miles the native resolution of the digicam. Video exceptional at some point of the day is very good and night time excellent is ideal, with an average improvement of night time satisfactory over the A118. notice a A119S version can be available with a view to have a Sony CMOS sensor and might improve night best as well.

one of the lawsuits of the A118 is that the video became grainy. The graininess has been reduced on the A119 however some graininess still exists. The video from the pre-production versions of this camera had a blueish tint however that has been corrected with the brand new firmware. Viofo has been pretty energetic in improving the firmware on this camera that’s a fine signal.

The camera comes with a 2″ display and an elective GPS mount is available. build fine is pretty good. the size of the A119 is 70mm x 50mm x 45mm, quite just like the A118. even as now not the smallest digicam, it’s miles very discreet because the camera mounts at once to the windshield rather than the use of a large mount. It also can be hooked up high up at the windshield in order that best the lens is visible from the out of doors.

For more:

The camera comes with G-sensor but does no longer have a buffered parking mode. An optionally available circular Polarizing Lens is available as nicely.

known troubles

warm pixels at night

a few owners of the preproduction models have indicated the digicam has hot pixels at night (vivid dots at the video). this may be corrected by calibrating the digital camera in engineering mode. To get into engineering mode, you may want to create a blank document named ENGMODE. the steps are as follows if the use of windows 10 (from our member Gibson99).

click begin, kind CMD, then hit input or click on the Command prompt icon.
carry out a short format of the SD card with this command:
format X: /Q
wherein X is the force letter of the SD card.
change to the pressure this is the SD card with the aid of surely typing X: (or some thing letter it’s far) and hit enter. the set off ought to now be X:>
Create the engmode report with this command:
echo. > ENGMODE
To verify that the document is there, type DIR and make sure it’s the best element listed except the 2 “dot” entries on the top.
Now you could near the dos window or type go out.
most crucial part is to soundly take away the sd card earlier than you physically remove it from the computer. Down within the decrease proper subsequent to the clock, there’s a photo of a USB thumb pressure – click it once and it will list the removable devices – click on the one for the SD card and it’ll let you know whilst it’s secure to dispose of it.
placed the SD card inside the camera and the digicam must be in ENGMODE
choose format SPI from the menu
factor the camera to some thing white with plenty of light (avoiding shadows) which include a white sheet of paper. pick DP bright from the menu and press the good enough button
cover the lens with foil paper in a dark room. complete black in a dark room and wait 10 mins (20-30 recommended) for the sensor temperature to stabilize, then press the Shutter button and wait for the following message to be shown on the display, the intense pixel calibration is then whole.
while the camera is pointing to a white sheet of paper, choose DP brilliant from the menu. Press ok when finished.
whilst the lens is blanketed with tin foil in a dark room perform pick DP dark from the menu. Wait 10 mins, then press the ok button. It must say DP exceeded completed

need to I buy?

The A119 is a pleasing improve to the A118 because of the higher video fine. The discreet wedge formed shape factor, correct build quality and GPS constructed into the mount makes this an awesome digital camera. The manufacturer has been making firmware updates that have progressed the overall performance of the digital camera. preliminary reliability is good however we are able to preserve song of how it plays as time goes on. universal, one of the quality cameras for the cash we’ve seen released in 2016. An excellent purchase. you could want to don’t forget the A119S if you are seeking out better night excellent.

See what other owners have to mention approximately the A119 on our discussion board.Firmware

caution! MAKING modifications to your FIRMWARE ARE achieved AT YOUR personal hazard. WE aren’t chargeable for ANY harm in your sprint CAM due to these commands.
Firmware replace commands

down load the firmware document
Unzip the document the use of an unzip application
Open the record and copy the .bin record directly onto the MicroSD card root document (use a 32GB most card, FAT32 format)
Insert the MicroSD card into the camera and strength it on via a 5V/1A power supply, e.g. cigarette lighter or strength bank, it will start improve mechanically.
at the same time as upgrading the the front REC purple LED starts offevolved blinking. The mild will blink slowly at the beginning, then it will blink fast. After the mild stops blinking, the upgrade is compete. note the firmware may be deleted automatically after the upgrade